{"id":23,"date":"2024-01-19T12:07:15","date_gmt":"2024-01-19T11:07:15","guid":{"rendered":"https:\/\/ctl.create.aau.dk\/?page_id=23"},"modified":"2026-01-26T11:53:06","modified_gmt":"2026-01-26T10:53:06","slug":"3-d-printing","status":"publish","type":"page","link":"https:\/\/ctl.create.aau.dk\/?page_id=23","title":{"rendered":"3 D Printers"},"content":{"rendered":"\n

Manufakturet has three Ultimaker 3 printers capable of a 215 x 215 x 200 mm build volume and two Bambu X1 Carbon printers capable of 256 x 256 x 256 mm build volume.<\/p>\n\n\n\n

\n\n\n\n
\n
\"\"<\/figure>\n\n\n\n
\n

Intro Course<\/h2>\n\n\n\n

Staff and students are required to take an introduction course before using the 3D printing facilities in CreaTech Lab.<\/p>\n\n\n\n

As of April 2025, the course was moved online. Use the link below.<\/p>\n\n\n\n

<\/p>\n\n\n\n

\n
Online 3D Printing Course<\/a><\/div>\n<\/div>\n\n\n\n

Once you have completed the course you can use the form<\/a> at towards the bottom of this page to gain card access to the 3D print room.<\/p>\n<\/div>\n\n\n\n

<\/p>\n<\/div>\n\n\n\n

\n\n\n\n

3D Printer Set-up<\/h2>\n\n\n\n
\n
\n
\n
\n
\n

The 3D printers in the lab are fitted out with a range of materials. Be sure to match the existing 3D printer set up with the settings within Cura.<\/p>\n<\/div><\/div>\n<\/div><\/div>\n\n\n\n

\"\"<\/figure>\n<\/div>\n<\/div>\n<\/div>\n\n\n\n

Do not attempt to change the settings on the printers themselves, or change the actual filaments.<\/p>\n\n\n\n

If you wish to do so you can download the lab Cura settings<\/a>Download<\/a><\/div>\n\n\n\n
\n\n\n\n

Materials, Prices and Payment<\/h2>\n\n\n\n
\n
\"\"<\/figure>\n\n\n\n
\n

We charge a set starting fee of 10 Kr, plus a per gram fee determined by the materials being used.<\/p>\n\n\n\n

If using the Lab 3D printing laptop<\/strong>, the price per weight is calculated for you, but remember to add the 10 kr per print run. Otherwise use the instructions below.<\/p>\n\n\n\n


You can see the weight of your print in Cura, before printing:<\/p>\n\n\n\n

After \u2019slicing\u2019 your print in Cura, the weight of the print and the length of filament will be displayed.<\/p>\n<\/div>\n<\/div>\n\n\n\n

Material<\/td>Price per gram<\/td><\/tr>
PLA (Good all-around material)<\/td>0.5 DKK<\/td><\/tr>
PVA (Water soluble, use only for supports)<\/td>1.5 DKK<\/td><\/tr>
Conductive PLA (Expensive, electrically conductive)<\/td>2.0 DKK<\/td><\/tr>
TPU95 (Tough, elastic material)<\/td>1.0 DKK<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

The example pictured Above would cost 25 Kr. (12g PLA at 0.5 DKK per gram + 6g PVA at 1.5 DKK per gram + 10 DKK)<\/p>\n\n\n\n

If your print is unsuccessful, please make an estimate of the amount of material used and pay accordingly.<\/p>\n\n\n\n

PAY USING MOBILEPAY: 84945
MAKE SURE TO ADD \u20193D PRINT\u2019 IN THE COMMENT FIELD.<\/p>\n\n\n\n

\n
MobilePay<\/a><\/div>\n<\/div>\n\n\n\n
\n\n\n\n

Print Room Access<\/h2>\n\n\n\n

If you have completed the online 3D printing Intro, you can use this form to ask for access to the print room. (If you have just passed the online course, you might not be whitelisted for this form for a few days.)<\/p>\n\n\n

<\/div>
<\/div>